- Welcome to Warrior System Support Forum.
Recent posts
#41
Warrior Hardware General Support / CPF CARD COMPONENT BURN DURING...
Last post by azahari - July 13, 2019, 01:48:24 AMHi Expert,
I would like to get you prompt advise and feedback on some issue that we had currently.
Reported by our Engineer onsite:
On 11th July we were logging GR-CCL tool while pulling out of the hole.
At depth of 12,900ft, all of a sudden engineer on site observed burn smell coming from the CPF Panel and noticed no voltage and current were monitored at the CPF Panel.
Tool signal also lost during this moment.
He then opened the CPF panel cover. Observed 2 panel cards got burnt component, the 2 card involved is ANASW card (C1 Component) and PSXD card (C5 Component).
Engineer onsite also measure the frequency of the power supply to the panel is as per requirement (110AC/ 60hz).
The operation continued by pulling the tool out of the hole.
Can we get your advice on what might cause the card component to burn?
FYI, this is the second occasion that we face a similar issue of burn card component, previous issue involved a difference CPF panel.
This morning we received an email from the client informing us to rig down from well and demob our equipment from the location due to the several technical issues that we have including this one.
We hope you understand our Urgency to get your response regarding this issue as we have to be in client office on Monday to explain the issue.
I would like to get you prompt advise and feedback on some issue that we had currently.
Reported by our Engineer onsite:
On 11th July we were logging GR-CCL tool while pulling out of the hole.
At depth of 12,900ft, all of a sudden engineer on site observed burn smell coming from the CPF Panel and noticed no voltage and current were monitored at the CPF Panel.
Tool signal also lost during this moment.
He then opened the CPF panel cover. Observed 2 panel cards got burnt component, the 2 card involved is ANASW card (C1 Component) and PSXD card (C5 Component).
Engineer onsite also measure the frequency of the power supply to the panel is as per requirement (110AC/ 60hz).
The operation continued by pulling the tool out of the hole.
Can we get your advice on what might cause the card component to burn?
FYI, this is the second occasion that we face a similar issue of burn card component, previous issue involved a difference CPF panel.
This morning we received an email from the client informing us to rig down from well and demob our equipment from the location due to the several technical issues that we have including this one.
We hope you understand our Urgency to get your response regarding this issue as we have to be in client office on Monday to explain the issue.
#42
General Discussion / Re: Setting TOPSHOT as depth s...
Last post by rwar - July 10, 2019, 10:36:31 AMAre you trying to display the actual measured depth of the top shot on the tool diagram? I don't believe that can be done with the current software.
If you are wanting to show the top shot relative to the tool zero point, you would need to have some tool module use the sensor you added. You might create a zero-length user defined tool for your sensor and carefully add it to the string in the right place.
If you are wanting to show the top shot relative to the tool zero point, you would need to have some tool module use the sensor you added. You might create a zero-length user defined tool for your sensor and carefully add it to the string in the right place.
#43
General Discussion / Setting TOPSHOT as depth senso...
Last post by crxmaniac - July 08, 2019, 05:44:08 PMI am adding TopShot in tooldiagram for perforations services. by adding sensor in service as TOPSHOT=AUX,,4
The sensor output will have a zero value.
I want the sensor output to give TOPSHOT depth.
Any ideas?
regards
The sensor output will have a zero value.
I want the sensor output to give TOPSHOT depth.
Any ideas?
regards
#44
General Discussion / Re: create their own well obje...
Last post by crxmaniac - July 06, 2019, 02:52:15 PMThanks 
#45
General Discussion / Re: create their own well obje...
Last post by kmilch - July 06, 2019, 01:06:06 PMFrom the Well Object Editor, select Help and search for 'user defined'.
#46
Warrior Software General Support / Re: "Read ASCII Data into Warr...
Last post by rwar - July 06, 2019, 12:30:21 PMWhat type are you trying to import? We maight be able to help you more if you sent us a sample.
#47
General Discussion / create their own well objects ...
Last post by crxmaniac - July 06, 2019, 08:16:46 AMIn the manual for warrior 8 Field operation Manual it states:
"It is possible for the User to create their own well objects to be used in a well sketch, but it is outside of the scope of this document. If this need"
Is there anyone knows how to do this?
"It is possible for the User to create their own well objects to be used in a well sketch, but it is outside of the scope of this document. If this need"
Is there anyone knows how to do this?
#48
Warrior Software General Support / Re: "Read ASCII Data into Warr...
Last post by erik - June 13, 2019, 08:23:52 AMYes Sir, I choose the right file
#49
How to use this forum / Re: Sondex PLT String with War...
Last post by rwar - June 07, 2019, 08:29:00 PMYou probably have a USB communication issue. Try changing USB cables; shorter, higher quality and/or active cables usually help.
#50
Warrior Software General Support / Re: "Read ASCII Data into Warr...
Last post by rwar - June 07, 2019, 08:26:06 PMAre you selecting the correct file type before you open the file?