Warrior Software General Support

Recording Clock Time

Started by mattparker

Replies: 7
Views: 20,078

January 27, 2015, 12:41:55 PM
by kmilch

Can't use Win7 with half of our panels - Unrecognized USB Device

Started by CPlus

Replies: 12
Views: 17,648

November 08, 2012, 04:24:32 PM
by CPlus

Warrior 8.12 running slow with Team viewer?

Started by 123

Replies: 2
Views: 16,929

June 10, 2020, 02:21:20 AM
by 123

Smart monitor Installation

Started by Boodimania

Replies: 4
Views: 16,865

December 02, 2008, 05:53:35 AM
by George

warrior configuration help with Sondex MIT 60F

Started by CPlus

Replies: 3
Views: 16,441

October 08, 2009, 09:19:23 AM
by adamg

Error Code 16384

Started by jhitt81

Replies: 3
Views: 16,420

December 11, 2013, 10:02:12 AM
by DLC

Possible to have both SDS Warrior panels and Sondex Midas on same pc?

Started by mawrick

Replies: 2
Views: 15,084

May 19, 2014, 09:17:58 AM
by Jerry

remove banner from plot

Started by corral

Replies: 3
Views: 14,872

October 09, 2014, 08:25:51 AM
by kmilch

Tension calibration - possible to add cal points? ? (and is 2 point good enough)

Started by mawrick

Replies: 2
Views: 14,785

August 09, 2016, 01:46:24 AM
by alioda

SDS warrior and Sondex Warrior on same PC

Started by alioda

Replies: 3
Views: 14,570

April 12, 2017, 12:43:31 AM
by alioda

demo mode not available after opening control panel

Started by reaton

Replies: 2
Views: 14,182

November 29, 2016, 12:01:22 PM
by reaton

Any way to optimize custom tool diagrams (or any reccomendations)

Started by mawrick

Replies: 2
Views: 14,181

May 23, 2014, 03:06:37 AM
by mawrick

"Read ASCII Data into Warrior" is NOT working

Started by erik

Replies: 3
Views: 14,126

July 06, 2019, 12:30:21 PM
by rwar

CNL calibrations

Started by cablehead

Replies: 1
Views: 14,074

June 19, 2014, 11:03:00 AM
by Jerry

Producing DLIS from DB file Pass

Started by alioda

Replies: 0
Views: 14,039

April 12, 2017, 12:46:11 AM
by alioda

SLAB?

Started by iancoates

Replies: 1
Views: 13,615

December 18, 2015, 11:08:48 AM
by Jerry

No specification found for sensor "TEMP2" - PRT can't initialize

Started by mawrick

Replies: 1
Views: 13,527

May 21, 2014, 08:14:44 AM
by mawrick

Write Protection

Started by corral

Replies: 1
Views: 13,525

October 06, 2014, 08:48:06 AM
by kmilch

Is depth slip control supported in Warrior ?

Started by mawrick

Replies: 1
Views: 13,440

May 19, 2014, 09:19:00 AM
by Jerry

Possible to rename a "tool group"

Started by mawrick

Replies: 1
Views: 13,200

May 17, 2014, 08:05:49 AM
by kmilch